Differences

This shows you the differences between two versions of the page.

--- infineon:cyusb231 [ 24.03.2026 20:38] – lars
+++ infineon:cyusb231 [ 07.06.2026 01:57] (current) – [Memory Map] lars
@@ Line 1: / Line 1: @@
 ====== EZ-USB FX2G3 ======
 USB 2.0 @ 480MHz (High Speed)
-Package: 104 LGA
-Temperaure range: -45 .. 85
+Package: 104 LGA (8x8mm)
+Temperaure range: -45 .. 85 °C
+Operating Voltage: 1.7V to 3.6 V
 GPIF/FIFO 16bit
 ===== Variants =====
 ^ part # ^ MCU ^ SRAM ^ Flash ^ SCB # ^ Peripherals ^
-| CYUSB2315-BF104AXI(T) | M0+ | 512 KB | 256 KB | 1 | I2C |
+| CYUSB2315-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 256 KB | 1 | I2C |
-| CYUSB2316-BF104AXI(T) | M0+ | 512 KB | 256 KB | 3 | I2C, SPI, CAN |
+| CYUSB2316-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 256 KB | 3 | I2C, SPI, CAN |
-| CYUSB2317-BF104AXI(T) | M0+ | 512 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI |
+| CYUSB2317-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI |
-| CYUSB2318-BF104AXI(T) | M4/M0+ | 1024 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI, Crypto |
+| CYUSB2318-BF104AXI(T) | M4(FP,MPU)@150 MHz/M0+(MPU)@100 MHz | 1024 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI, Crypto |
+<code>
+CY = Cypress
+  USB = USB Controller
+= USB 2.0
+      xxx = part number
+         -BF104AX = LGA Package
+                 I = Industrial
+                  T = Tape and reel
+</code>
+===== Memory Map =====
+^ start address ^ end address ^ used for ^ comment ^
+| 0x00 00 00 00 | 0x01 ff ff ff | Code | Program code region. Data can also be placed here. It includes the exception vector table, which starts at address 0. |
+| 0x00 00 00 00 | 0x00 01 ff ff | ROM | size = 128 kB |
+| 0x08 00 00 00 | 0x08 01 ff ff | SRAM | size = 128 kB |
+| 0x10 00 00 00 | 0x10 07 ff ff | Internal application flash | size = up to 512 kB |
+| 0x14 00 00 00 | 0x14 00 7f ff | Auxiliary flash, can be used for EEPROM Emulation | size = 32 kB |
+| 0x16 00 00 00 | 0x16 00 7f ff | SFlash | size = 32 kB |
+| 0x1c 00 00 00 | 0x1c 0f ff ff | High bandwidth DMA buffer SRAM | size = up to 1 MB |
+| 0x20 00 00 00 | 0x3f ff ff ff | reserved | |
+| 0x40 00 00 00 | 0x5f ff ff ff | Peripheral | All peripheral registers. Code cannot be executed from this region. CM4 bit-band in this region is not supported in EZ-USBTM FX2G3. |
+| 0x60 00 00 00 | 0x9f ff ff ff | external RAM | Quad SPI: Code can be executed from this region. |
+| 0xA0 00 00 00 | 0xDf ff ff ff | external device | not used |
+| 0xe0 00 00 00 | 0xe0 0f ff ff | Private Peripheral Bus | Provides access to peripheral registers within the CPU core |
+| 0xe0 10 0a 00 | 0xff ff ff ff | device | device specific system registers |
 ===== Pins =====
@@ Line 15: / Line 48: @@
   * A1..A56
   * B1..B48
+^ Pin ^ Signal name ^ description ^
+| ePAD | GND |  |
+| A1 | P0CTL2  |  |
+| A2 | P0CTL1  |  |
+| A3 | VDDIOXTAL |  |
+| A4 | XTALOUT |  |
+| A5 | XTALIN |  |
+| A6 | GND  |  |
+| A7 | V33 |  |
+| A8 | DPLUS |  |
+| A9 | DMINUS |  |
+| A10 | GND |  |
+| A11 | VDDD |  |
+| A12 | GND |  |
+| A13 | P0CLK |  |
+| A14 | Reserved |  |
+| A15 | I2C-SCL0 (SCB0) |  |
+| A15 | UART-RX0 (SCB0) |  |
+| A16 | I2C-SDA0 (SCB0) |  |
+| A16 | UART-TX0 (SCB0) |  |
+| A17 | VDDIO |  |
+| A18 | P0D0 |  |
+| A19 | P0D1 |  |
+| A20 | P0D2 |  |
+| A21 | P0D3 |  |
+| A22 | P0D4 |  |
+| A23 | P0D5 |  |
+| A24 | P0D6 |  |
+| A25 | P0D7 |  |
+| A26 | GND |  |
+| A27 | VDDIOP0_CTRL  |  |
+| A28 | GND |  |
+| A29 | P0CTL5 |  |
+| A30 | P0CTL6 |  |
+| A31 | P0CTL9  |  |
+| A32 | VDDIOP0 |  |
+| A33 | GPIO2 |  |
+| A33 | UART-TX0 |  |
+| A33 | I2C-SDA0 (SCB5) |  |
+| A33 | SPI-CS0 (SCB5) |  |
+| A33 | CAN1-RX |  |
+| A34 | PMODE |  |
+| A34 | SPI-MOSI (SCB5) |  |
+| A34 | CAN1-TX |  |
+| A35 | P0CTL0  |  |
+| A36 | GPIO1 |  |
+| A36 | UART-RX0 |  |
+| A36 | I2C-SCL0 (SCB5) |  |
+| A36 | SPICLK (SCB5) |  |
+| A37 | P0CTL3 |  |
+| A38 | P0CTL4 |  |
+| A39 | P0CTL7 |  |
+| A40 | P0CTL8 |  |
+| A41 | GND |  |
+| A42 | XRES |  |
+| A43 | VDDIOP0_CTRL |  |
+| A44 | VBUSDETECTN |  |
+| A45 | P0D8 |  |
+| A46 | P0D9 |  |
+| A47 | P0D10 |  |
+| A48 | P0D11 |  |
+| A49 | P0D12 |  |
+| A50 | P0D13 |  |
+| A51 | P0D14 |  |
+| A52 | P0D15 |  |
+| A53 | GND |  |
+| A54 | CLKOUT |  |
+| A55 | VDDIOP0 |  |
+| A56 | GND |  |
+| B1 | DNU |  |
+| B2 | DNU |  |
+| B3 | DNU |  |
+| B4 | DNU |  |
+| B5 | DNU |  |
+| B6 | DNU |  |
+| B7 | DNU |  |
+| B8 | GND |  |
+| B9 | DNU |  |
+| B10 | DNU |  |
+| B11 | DNU |  |
+| B12 | DNU |  |
+| B13 | DNU |  |
+| B14 | RESREF |  |
+| B15 | TDO / SWO |  |
+| B15 | PDM3-CLK0 |  |
+| B15 | UART-TX1 (SCB4) |  |
+| B15 | I2C-SCL1 (SCB4) |  |
+| B15 | SPICLK (SCB4) |  |
+| B16 | TDI |  |
+| B16 | PDM3-DATA0 |  |
+| B16 | UART-RX1 (SCB4) |  |
+| B16 | I2C-SDA1 (SCB4) |  |
+| B16 | SPICS0 (SCB4) |  |
+| B17 | TMS / SWDIO |  |
+| B17 | PDM3-CLK1 |  |
+| B17 | UART-RTS1 (SCB4) |  |
+| B17 | SPI-MOSI (SCB4) |  |
+| B18 | TCLKSWDCLK |  |
+| B18 | PDM3-DATA1 |  |
+| B18 | UART-CTS1 (SCB4) |  |
+| B18 | SPI-MISO (SCB4) |  |
+| B19 | GPIO |  |
+| B19 | SWDRST |  |
+| B20 | PDMDATA |  |
+| B20 | TCPWM4_N |  |
+| B21 | GPIO4 |  |
+| B21 | SPI-MISO (SCB5) |  |
+| B22 | SPICLK (SMIF)  |  |
+| B22 | UART-RX1 (SCB6) |  |
+| B22 | I2C-SCL1 (SCB6) |  |
+| B23 | SPICS0 (SMIF) |  |
+| B23 | UART-TX1 (SCB6) |  |
+| B23 | I2C-SDA1 (SCB6) |  |
+| B24 | SPICS1 (SMIF) |  |
+| B25 | CAN0-TX |  |
+| B25 | PDM0-DATA1 |  |
+| B25 | UART-TX0 (SCB4) |  |
+| B25 | I2C-SDA0 (SCB4) |  |
+| B25 | TCPWM2_N |  |
+| B25 | SPICS0 (SCB4) |  |
+| B26 | CAN0-RX |  |
+| B26 | PDM0-CLK1 |  |
+| B26 | UART-RX0 (SCB4) |  |
+| B26 | I2C-SCL0 (SCB4) |  |
+| B26 | TCPWM2_P |  |
+| B26 | SPICLK (SCB4) |  |
+| B27 | SPIDAT0 (SMIF) |  |
+| B27 | UART-RX1 (SCB0) |  |
+| B27 | I2C-SCL (SCB0) |  |
+| B27 | SPICLK (SCB2) |  |
+| B28 | SPIDAT1 (SMIF) |  |
+| B28 | UART-TX1 (SCB0) |  |
+| B28 | I2C-SDA (SCB0) |  |
+| B28 | SPICS0 (SCB2) |  |
+| B29 | SPIDAT2 (SMIF) |  |
+| B29 | UART-CTS0 (SCB0) |  |
+| B29 | SPI-MOSI (SCB2) |  |
+| B30 | SPIDAT3 (SMIF) |  |
+| B30 | UART-RTS0 (SCB0) |  |
+| B30 | SPI-MISO (SCB2) |  |
+| B31 | VDDIOQSPI |  |
+| B32 | SPIDAT4 (SMIF) |  |
+| B32 | UART-CTS0 (SCB2) |  |
+| B33 | SPIDAT5 (SMIF) |  |
+| B34 | SPIDAT6 (SMIF) |  |
+| B34 | UART-RX1 (SCB1) |  |
+| B34 | I2C-SDA1 (SCB1) |  |
+| B35 | SPIDAT7 (SMIF) |  |
+| B35 | UART-TX1 (SCB1) |  |
+| B35 | I2C-SCL1 (SCB1) |  |
+| B36 | DNU |  |
+| B37 | DNU |  |
+| B38 | GPIO5 |  |
+| B39 | GPIO6 |  |
+| B40 | VCCD |  |
+| B41 | DNU |  |
+| B42 | GPIO8 |  |
+| B43 | GPIO9 |  |
+| B44 | PDMCLK |  |
+| B44 | TCPWM4_P |  |
+| B45 | GPIO10 |  |
+| B46 | USB2DN2 |  |
+| B47 | USB2DP2 |  |
+| B48 | DNU |  |
@@ Line 20: / Line 220: @@
 ^ abbreviation ^ long version ^ comment ^
+| A/D | | analog-to-digital |
+| ABS | | absolute |
+| ABUS | | analog output bus |
+| AC | | alternating current |
+| ADC | | analog-to-digital converter |
+| AES | | Advanced Encryption Standard |
+| AHB | | AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM® data transfer bus |
+| Arm® | | Advanced RISC Machine, a CPU architecture |
+| API | | application programming interface |
+| APOR | | analog power-on reset |
+| BC | | broadcast clock |
+| BD | | buffer descriptors |
+| BOD | | brownout detection |
+| BOM | | bill-of-materials |
+| BR | | bit rate |
+| BRA | | bus request acknowledge |
+| BRQ | | bus request |
+| CAN | | controller area network |
+| CAN FD | | controller area network with flexible data rate |
+| CBS | | credit-based shaping |
+| CFI | | canonical format indicator |
+| CI | | carry in |
+| CMOS | | complementary metal-oxide-semiconductor |
+| CMP | | compare |
+| CO | | carry out |
+| CPHA(SPI) | | clock phase |
+| CPOL(SPI) | | clock polarity |
+| CPU | | central processing unit |
+| CPUSS | | CPU subsystem |
+| CRC | | cyclic redundancy check, an error-checking protocol |
+| CSD | | CAPSENSETM sigma delta |
+| CSV | | clock supervisor |
+| CT | | continuous time |
+| CTBm | | continuous time block-mini |
+| DAC | | digital-to-analog converter |
+| DC | | direct current |
+| DDR | | double data rate (also see SDR) |
+| DES | | data encryption standard |
+| DI | | digital or data input |
+| DMA | | direct memory access |
+| DNL | | differential nonlinearity |
+| DNU | Do not use | Do not use these connections for PCB signal routing channels. Do not connect any host system signal to these connections. |
+| DO | | digital or data output |
+| DSI | | digital signal interface |
+| DSM | | Deep Sleep mode |
+| DW | | data wire, same as P-DMA |
+| ECC | | error correcting code |
+| ECO | | external crystal oscillator |
+| EEE | | Energy Efficient Ethernet (IEEE Std 802.3az) |
+| EEPROM | | electrically erasable programmable read only memory |
+| EMIF | | external memory interface |
+| EOF | | end of frame |
+| ETM | | embedded trace macrocell |
+| FB | | feedback |
+| FCS | | frame check sequence |
+| FIFO | | first in first out |
+| FLL | | frequency locked loop |
+| FPU | | floating point unit |
+| FSR | | full scale range |
+| GHS | | Green Hills tool chain with IDE |
+| GPIO | | general purpose I/O |
+| HCI | | host-controller interface |
+| HFCLK | | high-frequency clock |
+| HSIOM | | high-speed I/O matrix |
+| HSM | | hardware security module |
+| I2C | | inter-integrated circuit |
+| IDE | | integrated development environment |
+| IF | | interface |
+| ILO | | internal low-speed oscillator |
+| IMO | | internal main oscillator |
+| INL | | integral nonlinearity |
+| I/O | | input/output |
+| IOR | | I/O read |
+| IOW | | I/O write |
+| IP | | Internet protocol |
+| IPC | | inter-processor communication |
+| IPG | | inter-packet gap |
+| IRA | | interrupt request acknowledge |
+| IrDA | | infrared interface |
+| IRES | | initial power on reset |
+| IRQ | | interrupt request |
+| ISR | | interrupt service routine |
+| IVR | | interrupt vector read |
+| JTAG | | Joint Test Action Group |
+| L2CAP | | logical link control and adaptation protocol |
+| LAN | | local area network (IEEE Std 802) |
+| LLDP | | link layer discovery protocol (IEEE Std 802.1AB) |
+| LPCOMP | | low-power comparator |
+| LPI | | low-power idle (IEEE Std 802.3az) |
+| LRb | | last received bit |
+| LRB | | last received byte |
+| LSb | | least significant bit |
+| LSB | | least significant byte |
+| LUT | | lookup table |
+| LVD | | low-voltage detection |
+| MAC | | media access control (IEEE Std 802) |
+| MCU | | microcontroller unit |
+| MCWDT | | multi-counter watchdog timer |
+| M-DMA | | memory-direct memory access |
+| MDC | | management data clock |
+| MII | | media independent interface |
+| MISO | | master-in-slave-out |
+| MMIO | | memory mapped input/output |
+| MOSI | | master-out-slave-in |
+| MPU | | memory protection unit |
+| MSb | | most significant bit |
+| MSB | | most significant byte |
+| NC | Not connected | The connection may safely be used for routing space for a signal on a PCB. However, any signal connected to an NC pin must not have voltage levels higher than VIO. |
+| NSP | | non-standard preamble |
+| NVIC | | nested vectored interrupt controller |
+| OTA | | over-the-air programming |
+| OTP | | one-time programmable |
+| OVD | | overvoltage detection |
+| P-DMA | | peripheral-direct memory access same as DW |
+| PC | | program counter |
+| PCH | | program counter high |
+| PCL | | program counter low |
+| PCS | | physical coding sublayer |
+| PD | | power down |
+| PFC | | priority-based flow control (IEEE Std 802.1Qbb) |
+| PGA | | programmable gain amplifier |
+| PHY | | physical sublayer |
+| PLL | | phase-locked loop |
+| PM | | power management |
+| PMA | | PSOCTM memory arbiter |
+| POR | | power-on reset |
+| PPB | | private peripheral bus |
+| PPOR | | precision power-on reset |
+| PPPoE | | point-to-point protocol over ethernet |
+| PPU | | peripheral protection unit |
+| PRNG | | Pseudo-Random Number Generator |
+| PRS | | pseudo random sequence |
+| PSRR | | power supply rejection ratio |
+| PSSDC | | power system sleep duty cycle |
+| PTP | | precision time protocol (IEEE Std 1588) |
+| PWM | | pulse width modulator |
+| RAM | | random-access memory |
+| RETI | | return from interrupt |
+| RFU | Reserved for Future use | Do not use RFU connectors for PCB routing channels so that the PCB may take advantage of future enhanced features in devices with a compatible footprint. |
+| RF | | radio frequency |
+| RISC | | reduced-instruction-set computing |
+| ROM | | read only memory |
+| RTC | | real-time clock |
+| RW | | read/write |
+| RX | | reception |
+| SAR | | successive approximation register |
+| SC | | switched capacitor |
+| SCB | | serial communication block |
 | SCB | Serial Control Block | A peripheral that can be used as I2C, UART or SPI |
+| SCL | | I2C serial clock |
+| SDA | | I2C serial data |
+| SDR | | single data rate (also see DDR) |
+| SE0 | | single-ended zero |
+| SECDED | | single error correction double error detection |
+| SerDes | | serializer/deserializer |
+| SHA | | secure hash algorithm |
+| SHE | | secure hardware extension |
+| SFD | | start of frame delimiter |
+| SGMII | | serial Gigabit media independent interface |
+| SIE | | serial interface engine |
+| SIO | | special I/O |
+| SMIF | | serial memory interface |
+| SMPU | | shared memory protection unit |
+| SNAP | | subnetwork access protocol |
+| SNR | | signal-to-noise ratio |
+| SOF | | start of frame |
+| SOI | | start of instruction |
+| SP | | stack pointer |
+| SPD | | sequential phase detector |
+| SPI | | serial peripheral interface, a communications protocol |
+| SPI | | serial peripheral interconnect |
+| SPIM | | serial peripheral interconnect master |
+| SPIS | | serial peripheral interconnect slave |
+| SRAM | | static random-access memory |
+| SRSS | | system resources sub-system |
+| SROM | | supervisory read only memory |
+| SSADC | | single slope ADC |
+| SSC | | supervisory system call |
+| SYSCLK | | system clock |
+| SWD | | single wire debug |
+| Tbit | | bit period |
+| TC | | terminal count |
+| TCP | | transfer control protocol |
+| TCPWM | | timer/counter pulse-width modulator |
+| TD | | transaction descriptors |
+| TTL | | transistor-transistor logic |
+| TRNG | | True Random Number Generator |
+| TS | | timestamp |
+| TSU | | timestamp unit|
+| TX | | transmission |
+| UART | | Universal Asynchronous Transmitter Receiver, a communications protocol |
+| UDB | | universal digital block |
+| UDP | | user datagram protocol |
+| USB | | Universal Serial Bus |
+| USBIO | | USB I/O |
+| VLAN | | Virtual LAN (IEEE Std 802.1Q) |
+| WCO | | watch crystal oscillator |
+| WDT | | watchdog timer / watchdog timer reset |
+| WDR | | watchdog reset |
+| XIP | | execute-in-place |
+| XRES | | external reset |
+| XRES_N | | external reset, active LOW |
+| XRES_L | | external reset I/O pin (active LOW) |
+| XTAL | | crystal |