infineon:cyusb231
This is an old revision of the document!
Table of Contents
EZ-USB FX2G3
USB 2.0 @ 480MHz (High Speed)
Package: 104 LGA (8x8mm)
Temperaure range: -45 .. 85 °C
Operating Voltage: 1.7V to 3.6 V
GPIF/FIFO 16bit
Variants
| part # | MCU | SRAM | Flash | SCB # | Peripherals |
|---|---|---|---|---|---|
| CYUSB2315-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 256 KB | 1 | I2C |
| CYUSB2316-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 256 KB | 3 | I2C, SPI, CAN |
| CYUSB2317-BF104AXI(T) | M0+(MPU)@100 MHz | 512 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI |
| CYUSB2318-BF104AXI(T) | M4(FP,MPU)@150 MHz/M0+(MPU)@100 MHz | 1024 KB | 512 KB | 6 | I2C, SPI, CAN, QSPI, Crypto |
Pins
- ePad
- A1..A56
- B1..B48
| Pin | Signal name | description |
|---|---|---|
| ePAD | GND | |
| A1 | P0CTL2 | |
| A2 | P0CTL1 | |
| A3 | VDDIOXTAL | |
| A4 | XTALOUT | |
| A5 | XTALIN | |
| A6 | GND | |
| A7 | V33 | |
| A8 | DPLUS | |
| A9 | DMINUS | |
| A10 | GND | |
| A11 | VDDD | |
| A12 | GND | |
| A13 | P0CLK | |
| A14 | Reserved | |
| A15 | I2C-SCL0 (SCB0) | |
| A15 | UART-RX0 (SCB0) | |
| A16 | I2C-SDA0 (SCB0) | |
| A16 | UART-TX0 (SCB0) | |
| A17 | VDDIO | |
| A18 | P0D0 | |
| A19 | P0D1 | |
| A20 | P0D2 | |
| A21 | P0D3 | |
| A22 | P0D4 | |
| A23 | P0D5 | |
| A24 | P0D6 | |
| A25 | P0D7 | |
| A26 | GND | |
| A27 | VDDIOP0_CTRL | |
| A28 | GND | |
| A29 | P0CTL5 | |
| A30 | P0CTL6 | |
| A31 | P0CTL9 | |
| A32 | VDDIOP0 | |
| A33 | GPIO2 | |
| A33 | UART-TX0 | |
| A33 | I2C-SDA0 (SCB5) | |
| A33 | SPI-CS0 (SCB5) | |
| A33 | CAN1-RX | |
| A34 | PMODE | |
| A34 | SPI-MOSI (SCB5) | |
| A34 | CAN1-TX | |
| A35 | P0CTL0 | |
| A36 | GPIO1 | |
| A36 | UART-RX0 | |
| A36 | I2C-SCL0 (SCB5) | |
| A36 | SPICLK (SCB5) | |
| A37 | P0CTL3 | |
| A38 | P0CTL4 | |
| A39 | P0CTL7 | |
| A40 | P0CTL8 | |
| A41 | GND | |
| A42 | XRES | |
| A43 | VDDIOP0_CTRL | |
| A44 | VBUSDETECTN | |
| A45 | P0D8 | |
| A46 | P0D9 | |
| A47 | P0D10 | |
| A48 | P0D11 | |
| A49 | P0D12 | |
| A50 | P0D13 | |
| A51 | P0D14 | |
| A52 | P0D15 | |
| A53 | GND | |
| A54 | CLKOUT | |
| A55 | VDDIOP0 | |
| A56 | GND | |
| B1 | DNU | |
| B2 | DNU | |
| B3 | DNU | |
| B4 | DNU | |
| B5 | DNU | |
| B6 | DNU | |
| B7 | DNU | |
| B8 | GND | |
| B9 | DNU | |
| B10 | DNU | |
| B11 | DNU | |
| B12 | DNU | |
| B13 | DNU | |
| B14 | RESREF | |
| B15 | TDO / SWO | |
| B15 | PDM3-CLK0 | |
| B15 | UART-TX1 (SCB4) | |
| B15 | I2C-SCL1 (SCB4) | |
| B15 | SPICLK (SCB4) | |
| B16 | TDI | |
| B16 | PDM3-DATA0 | |
| B16 | UART-RX1 (SCB4) | |
| B16 | I2C-SDA1 (SCB4) | |
| B16 | SPICS0 (SCB4) | |
| B17 | TMS / SWDIO | |
| B17 | PDM3-CLK1 | |
| B17 | UART-RTS1 (SCB4) | |
| B17 | SPI-MOSI (SCB4) | |
| B18 | TCLKSWDCLK | |
| B18 | PDM3-DATA1 | |
| B18 | UART-CTS1 (SCB4) | |
| B18 | SPI-MISO (SCB4) | |
| B19 | GPIO | |
| B19 | SWDRST | |
| B20 | PDMDATA | |
| B20 | TCPWM4_N | |
| B21 | GPIO4 | |
| B21 | SPI-MISO (SCB5) | |
| B22 | SPICLK (SMIF) | |
| B22 | UART-RX1 (SCB6) | |
| B22 | I2C-SCL1 (SCB6) | |
| B23 | SPICS0 (SMIF) | |
| B23 | UART-TX1 (SCB6) | |
| B23 | I2C-SDA1 (SCB6) | |
| B24 | SPICS1 (SMIF) | |
| B25 | CAN0-TX | |
| B25 | PDM0-DATA1 | |
| B25 | UART-TX0 (SCB4) | |
| B25 | I2C-SDA0 (SCB4) | |
| B25 | TCPWM2_N | |
| B25 | SPICS0 (SCB4) | |
| B26 | CAN0-RX | |
| B26 | PDM0-CLK1 | |
| B26 | UART-RX0 (SCB4) | |
| B26 | I2C-SCL0 (SCB4) | |
| B26 | TCPWM2_P | |
| B26 | SPICLK (SCB4) | |
| B27 | SPIDAT0 (SMIF) | |
| B27 | UART-RX1 (SCB0) | |
| B27 | I2C-SCL (SCB0) | |
| B27 | SPICLK (SCB2) | |
| B28 | SPIDAT1 (SMIF) | |
| B28 | UART-TX1 (SCB0) | |
| B28 | I2C-SDA (SCB0) | |
| B28 | SPICS0 (SCB2) | |
| B29 | SPIDAT2 (SMIF) | |
| B29 | UART-CTS0 (SCB0) | |
| B29 | SPI-MOSI (SCB2) | |
| B30 | SPIDAT3 (SMIF) | |
| B30 | UART-RTS0 (SCB0) | |
| B30 | SPI-MISO (SCB2) | |
| B31 | VDDIOQSPI | |
| B32 | SPIDAT4 (SMIF) | |
| B32 | UART-CTS0 (SCB2) | |
| B33 | SPIDAT5 (SMIF) | |
| B34 | SPIDAT6 (SMIF) | |
| B34 | UART-RX1 (SCB1) | |
| B34 | I2C-SDA1 (SCB1) | |
| B35 | SPIDAT7 (SMIF) | |
| B35 | UART-TX1 (SCB1) | |
| B35 | I2C-SCL1 (SCB1) | |
| B36 | DNU | |
| B37 | DNU | |
| B38 | GPIO5 | |
| B39 | GPIO6 | |
| B40 | VCCD | |
| B41 | DNU | |
| B42 | GPIO8 | |
| B43 | GPIO9 | |
| B44 | PDMCLK | |
| B44 | TCPWM4_P | |
| B45 | GPIO10 | |
| B46 | USB2DN2 | |
| B47 | USB2DP2 | |
| B48 | DNU |
abbreviation dictionary
| abbreviation | long version | comment |
|---|---|---|
| ABUS | analog output bus | |
| AC | alternating current | |
| ADC | ||
| AHB | AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM® data transfer bus | |
| API | application programming interface | |
| APOR | analog power-on reset | |
| BC | broadcast clock | |
| BOM | bill-of-materials | |
| BR | bit rate | |
| BRA | bus request acknowledge | |
| BRQ | bus request | |
| CAN | controller area network | |
| CI | carry in | |
| CMP | compare | |
| CO | carry out | |
| CPU | central processing unit | |
| CRC | cyclic redundancy check | |
| CSD | CAPSENSETM sigma delta | |
| CT | continuous time | |
| CTBm | continuous time block-mini | |
| DAC | digital-to-analog converter | |
| DC | direct current | |
| DI | digital or data input | |
| DMA | direct memory access | |
| DNL | differential nonlinearity | |
| DNU | Do not use | Do not use these connections for PCB signal routing channels. Do not connect any host system signal to these connections. |
| DO | digital or data output | |
| DSI | digital signal interface | |
| DSM | Deep Sleep mode | |
| ECO | external crystal oscillator | |
| EEPROM | electrically erasable programmable read only memory | |
| EMIF | external memory interface | |
| FB | feedback | |
| FIFO | first in first out | |
| FSR | full scale range | |
| GPIO | general purpose I/O | |
| HCI | host-controller interface | |
| HFCLK | high-frequency clock | |
| I2C | inter-integrated circuit | |
| IDE | integrated development environment | |
| ILO | internal low-speed oscillator | |
| IMO | internal main oscillator | |
| INL | integral nonlinearity | |
| I/O | input/output | |
| IOR | I/O read | |
| IOW | I/O write | |
| IRES | initial power on reset | |
| IRA | interrupt request acknowledge | |
| IRQ | interrupt request | |
| ISR | interrupt service routine | |
| IVR | interrupt vector read | |
| L2CAP | logical link control and adaptation protocol | |
| LPCOMP | low-power comparator | |
| LRb | last received bit | |
| LRB | last received byte | |
| LSb | least significant bit | |
| LSB | least significant byte | |
| LUT | lookup table | |
| MISO | master-in-slave-out | |
| MMIO | memory mapped input/output | |
| MOSI | master-out-slave-in | |
| MSb | most significant bit | |
| MSB | most significant byte | |
| NC | Not connected | The connection may safely be used for routing space for a signal on a PCB. However, any signal connected to an NC pin must not have voltage levels higher than VIO. |
| PC | program counter | |
| PCH | program counter high | |
| PCL | program counter low | |
| PD | power down | |
| PGA | programmable gain amplifier | |
| PM | power management | |
| PMA | PSOCTM memory arbiter | |
| POR | power-on reset | |
| PPOR | precision power-on reset | |
| PRS | pseudo random sequence | |
| PSRR | power supply rejection ratio | |
| PSSDC | power system sleep duty cycle | |
| PWM | pulse width modulator | |
| RAM | random-access memory | |
| RETI | return from interrupt | |
| RFU | Reserved for Future use | Do not use RFU connectors for PCB routing channels so that the PCB may take advantage of future enhanced features in devices with a compatible footprint. |
| RF | radio frequency | |
| ROM | read only memory | |
| RW | read/write | |
| SAR | successive approximation register | |
| SC | switched capacitor | |
| SCB | serial communication block | |
| SCB | Serial Control Block | A peripheral that can be used as I2C, UART or SPI |
| SIE | serial interface engine | |
| SIO | special I/O | |
| SE0 | single-ended zero | |
| SNR | signal-to-noise ratio | |
| SOF | start of frame | |
| SOI | start of instruction | |
| SP | stack pointer | |
| SPD | sequential phase detector | |
| SPI | serial peripheral interconnect | |
| SPIM | serial peripheral interconnect master | |
| SPIS | serial peripheral interconnect slave | |
| SRAM | static random-access memory | |
| SRSS | system resources sub-system | |
| SROM | supervisory read only memory | |
| SSADC | single slope ADC | |
| SSC | supervisory system call | |
| SYSCLK | system clock | |
| SWD | single wire debug | |
| TC | terminal count | |
| TD | transaction descriptors | |
| UART | universal asynchronous receiver/transmitter | |
| UDB | universal digital block | |
| USB | Universal Serial Bus | |
| USBIO | USB I/O | |
| WCO | watch crystal oscillator | |
| WDT | watchdog timer | |
| WDR | watchdog reset | |
| XRES | external reset | |
| XRES_N | external reset, active LOW |
infineon/cyusb231.1779152846.txt.gz · Last modified: by lars